GRAPHIC TAKE-OFF METHOD (II)

***VER "WATER JET CUTTING BLOG" $139,500.00 New - 2012 SPECIFICATIONS: X-Axis travel............................................................120" Y-Axis travel.............................................................60" Z-Axis travel............................................................4.5" Pump output........................................................66,000 PSI Table length.............................................................168" Table width...............................................................90" Dimensions - approximate (excluding pumps & hopper)..........14' x 8' x 7'(H) Weight - approximate (without water)...............................5,000 Lbs. Weight - approximate (with water).................................15,000 Lbs. EQUIPPED WITH: AT2010 CNC controller Softec Waterjet Cutter software ESP 66 Pump PAC 60 5-axis cutter head Adjustable water height control for submerged cutting 60-degree beveling capacity 0.9 INCHES/MINUTE *Preliminary specifications subject to verification
  CALCULO DE LA HORA PRODUCCION NOMBRE DE EL EQUIPO: TECHNI WATERJET DATOS: PRECIO ORIGINAL $139,500.00 
 VIDA EN HORAS 12000
VALOR DE DE RESCATE $20,925.00 
 CUTTING VELOCITY 0.1 TO 3000 "/MIN
 CARGO FORMULA 
 CALCULO COSTO POR HORA DE LA MAQUINA DEPRECIACION = (Va-Vr/Ve (139500-20925)/12000 = 9.88 $/HR
 Va=$ 139,500.00 
 Va=VALOR DE ADQUISICION
 Vr= $ 20,925.00 Vr=VALOR DE RESCATE DE LA MAQUINA 5%
 Ve=12000 Ve=VIDA ECONOMICA EN HORAS INVERSION =(Va+Vr)i/2Ha 13.37 =13.37 $/HR i=TASA DE EINTERES i=9%
Ha=HORAS DE VIDA DE LA MAQUINA EN UN ANO (1200 HRS/WEEK) Ha=1250
 SEGUROS =(Va+Vr)S/2Ha 256.68 =0.02 $/HR S=PRIMA DE SEGUROS
 ALMACENAJE =KaD=                 0.20 $/HR
 D=DEPRECIACION POR HORA EFECTIVA DE TRABAJO D=.02
 Ka= COEFICIENTE EXPERIMENTAL O CALCULADO
 MANTENIMIENTO =QD = 0.79 $/HR Q=.08 Q=COEFICIENTA EXPERIMENTAL COMBUSTIBLES =cPc ELECTRICIDAD 220VOLTS 6.00 c=CANTIDAD NECESARIA DE COMBUSTIBLE POR HORA EFECTIVA DE TRABAJO=    0.6 $/KW-HR
 Pc= PRECIO UNITARIO DE EL COMBUSTIBLE LUBRICANTES =aPl
 a=CANTIDAD DE ARENA USADA PARA CORTAR POR HORA EFECTIVA DE TRABAJO ABRASIVE GARNETT
 LLANTAS =VII/Hv ************************************************(NO APLICA)
 OPERACION =Sa/H Sa=SALARIO POR TURNO DE EL PERSONAL
 H= HORAS TRABAJADAS POR LA MAQUINA =37.4 $/HR
 TOTAL COST 44.41 $/HR


 







NOTE: SEE AASHTO BRIDGE STEEL BLOG




Comments

Post a Comment

Popular posts from this blog

Image
  UNDERWATER CUTTING Courtesy of Broco BROCO BROCO CUTTING MANUAL P.O. BOX 1758 POMONA, CA 91769 714 623 2544                                                                                                                          Made by divers for divers: 1.- BROCO ROD 18” (45.72 CM)LONG INSULATED WRAPPED    ...
Read more

CAMBER

Image
  Cold cambering is the most common method used in fabrication shops to induce camber in a steel member, as it is a simpler and more cost-effective method than heat cambering.  This method uses a mechanically induced force to achieve the desired curvature. The member (I – beam) is placed in a device called a cambering machine that is often built by the fabricator but is also commercially available. The cambering machine consists of two restrained pivots, one near each end of the beam and one or two hydraulic jacks near the middle of the beam.  The jacks apply a force to induce camber into the member. After placing the member at the restrained end pivots, the rams of the hydraulic jack or jacks are advanced to apply stress into the member past it’s yield point to produce a permanent deflection. When the rams are retracted, the residual deformation remains.  The beam may need to be moved back and forth to actuate the jacking forces at different locations along the leng...
Read more